固定化微生物强化处理对甲苯胺模拟废水的研究

采用新型固定化载体大孔吸附树脂X-5固定化微生物强化SBR处理对甲苯胺模拟废水,与对照组相比,通过投加大孔吸附树脂X-5固定化微生物可以有效提高反应器的处理效率.在进水TOC浓度为434.8 mg/L,对甲苯胺浓度为326.9 mg/L的条件下,强化组可在100 min左右将TOC和对甲苯胺基本去除完全,去除率在99%以上.对照组则需要300min才能达到相近的去除效果.强化组对氨氮同样具有较好的硝化效果,出水氨氮浓度在10 mg/L以下.     

X-42钢在碳酸钠-碳酸氢钠溶液中慢拉伸时电化学噪音信号的小波分析

本文应用小波分析理论研究了X42管线钢在0.5 mol/l Na2CO3 1 mol/l NaHCO3溶液中,在-950mVSCE、-1100mVSCE阴极极化条件下,慢应变速率实验过程中的极化电流信号.结果表明,极化电流信号的低频部分代表着其发展趋势.在阴极极化时,由于阴极析氢造成的体系pH值升高,因而电流信号有逐渐增大的趋势.而且,在对SSRT过程中阴极极化电流信号进行分析时,并未发现第二类间断点.因此,对于工业腐蚀监控,是否可用出现第二类间断点来预测X-42钢在土壤中的应力腐蚀失效,还有待于进一步的研究与探讨.     

曲霉菌丝球HX对偶氮染料的吸附脱色

采用富积和驯化方法选育出的曲霉菌丝球HX对不同种类染料表现出高效吸附性能，可在12h内完全吸附200mg／L的直接染料、分散染料及活性黄X-R的颜色，并且研究了碳源质量浓度、氮源质量浓度、盐度、培养条件及优化条件组合对菌丝球HX吸附活性艳红X-3B的影响，结果表明：随碳源质量浓度的增加，吸附率相应增加，质量浓度为10．0g／L以上时，72h及以上的吸附率大于92．3％；氮源质量浓度高于0．75g／L时对吸附率影响不大；随盐度增加，染料吸附率有所下降．在温度为25～35℃、染料培养基pH为5．0～7．0、供氧充足的条件下吸附率较高．在所筛选的最佳吸附条件下，菌丝球HX对活性艳红X-3B表现出了更好的吸附效果．图6表3参9     

超声/镁粉体系协同降解活性艳红

研究了超声/镁粉体系对偶氮染料活性艳红X-3B的降解效果,探讨了溶液pH值、声强、镁粉投加量、辐照时间等因素对染料脱色率的影响。结果表明,当溶液pH=3.5,声强=54.3W/cm2,镁粉投加量为2.122g/L时,20mg/L活性艳红溶液在超声辐照48min后脱色率达99.71%。同时探讨了超声波/镁粉体系的协同降解作用。超声波强化镁粉降解的能力主要表现在机械振荡加速了染料向镁粉表面的传质速度;加入镁粉促进超声产生大量·OH,强化了对染料的声化学脱色和降解。超声波/镁粉联用具有显著协同作用,服从动力学一级反应。     

剩余污泥浓缩脱水投药量优化和模型建立

应用高分子阳离子絮凝剂（CPF-100）和聚丙烯酰胺（PAM）对污水厂剩余污泥进行浓缩脱水实验，研究表明：CPF-100的浓缩脱水效果优于PAM；当CPF-00投加量为1．16‰时，污泥沉降性能改善程度为37．51％；且在CPF-100投加量逐渐增大的初始阶段，污泥沉降性能改善程度随投加量的增加而增大，但CPF-100投加量也不宜过大，当CPF-100投加量超过1．16‰后，反而会使浓缩脱水效果变差。同时，建立了污泥沉降性能改善程度与絮凝剂CPF-100投加量、沉降时间之间的数学模型，其能较好地反映污水厂剩余污泥的浓缩脱水效果。     

Efficient removal of polybrominated diphenyl ethers from soil washing effluent by dummy molecular imprinted adsorbents: Selectivity and mechanisms

Surfactant enhanced elution is an effective method for removing hydrophobic organic pollutants from soils. The key to the development of leaching technology is selective removal of targeted pollutants in soil washing effluent and recycling of surfactant solutions. In this study, a molecular imprinting technique was applied to selectively sorb polybrominated diphenyl ethers (PBDEs) in soil washing effluent. The novel molecular imprinted polymers (MIPs) using different template molecules were synthesized by precipitation polymerization. Adsorption behaviors and mechanisms of MIPs were studied through experiments and theoretical calculations. The results show that 4-bromo-4′-hydroxybiphenyl and toluene can be effective imprinting molecule for MIPs synthesis. The maximal adsorption capacity of selected dummy molecular imprinted polymer (D₁-MIP) was 1032.36 µmol/g, and that of part molecular imprinted polymer (P-MIP) was 981.13 µmol/g. Their imprinting factors in 5 PBDEs adsorption ranged from 2.13 to 5.88, the recovery percentage of Triton X-100 can reach 99.09%, confirming the feasibility of reusing surfactant. Various PBDEs could be removed by MIPs, and Quantitative Structure Property Relationship analysis revealed that PBDEs’ molecular volume, planarity, polarity, and hydrophobicity have major influences on their adsorption performance. DFT calculation revealed that Van der Waals force and hydrogen bonding played important roles during selective adsorption. These results can provide effective theoretical guidance for surfactant enhanced soil elution in practical engineering applications.     

Catalytic ozonation of reactive red X-3B in aqueous solution under low pressure: decolorization and OH· generation

Catalytic ozonation of Reactive Red X-3B in aqueous solution had been carried out in an ozone oxidation reactor where Mn-Fe-ceramic honeycomb was used as the catalysts. The presence of Mn-Fe-ceramic honeycomb catalyst could obviously improve the decoloration efficiency of Reactive Red X-3B and the utilization efficiency of ozone compared to the results from non-catalytic ozonation. Adsorption of Reactive Red X-3B had no obviously influence on the degradation efficiency. Addition of tert-butanol significantly decreased the degradation efficiency, indicating that the degradation of Reactive Red X-3B followed the mechanism of hydroxyl radical (OH·) oxidation. The operating variables such as reaction pressure and ozone supply had a positive influence on the degradation efficiency, mainly attributing to facilitate the ozone decomposition and OH· formation.     

玻璃纤维负载P25光催化接触氧化活性艳红X-3B

在玻璃纤维上焙烧P25制备了负载型TiO2光催化剂,探讨了焙烧温度对催化活性的影响,设计了光催化接触氧化反应器,并以活性艳红X-3B为模型污染物,考察溶液pH值、共存阴离子(CO₃^2-、SO₄^2-、Cl-)对光催化反应的影响.结果表明,焙烧温度直接影响负载后催化剂的活性,300℃负载时活性最高,SEM照片显示此时P25与载体结合牢固、负载颗粒均匀.酸性条件对活性艳红X-3B的降解有利,当溶液初始pH由2.0上升到10.0时,活性艳红X-3B的降解率从90.06%下降至42.71%.共存的CO₃^2-、SO₄^2-对活性艳红X-3B降解的影响不大,但Cl^-对氧化过程有明显的抑制,使活性艳红X-3B的降解率下降17.03%.利用成熟的光催化剂P25,通过烧结的方法制备负载型催化剂是当前替代粉末催化剂的较为可行的方案.     

A fast and reliable method for quantitative determination of total mercury in vegetables

A cloud-point extraction (CPE) process using the nonionic surfactant, polyethylene glycol tert octylphenyl ether (Triton X-114) was employed for determination of Hg(II) ions in aqueous solutions. The method is based on the ion-pairing reaction of Hg(II) with Pyronin B (PyrB⁺) in the presence of excess iodide at pH 6.0 and extraction of the complex formed. The chemical variables affecting CPE efficiency were studied, and the analytical characteristics of the method were obtained. The calibration curves were linear in the range of 1–40 μg L^?1 with the detection limits of 0.35 and 0.30 μg L^?1 at 556 and 521 nm. Selectivity was also tested. The coefficients of variation of the method are 2.4% and 5.2% for five replicate measurements of mercury at levels of 10 and 25 μg L^?1, respectively. The results obtained for two certified reference samples were in a good agreement with the certified values. The method was applied to the determination of total mercury in vegetable samples.     

Bi2WO6可见光催化降解活性艳红X-3B的研究

采用水热合成法制备Bi2WO6催化剂,并通过XRD,UV-vis DRS等手段对其进行表征;以活性艳红X-3B为目标污染物,研究催化剂量、X-3B初始浓度、反应溶液pH值以及H2O2等因素在可见光辐射下对其光催化降解效果的影响.结果表明,所制备的Bi2WO6催化剂结晶度好,具有较强的可见光吸收能力;最佳催化反应条件为: X-3B初始浓度20mg/L,Bi2WO6用量2g/L, pH5.18(原始pH值).在此条件下,光照60min,对X-3B的去除率可达到86%;加入2mL/L 30%的H2O2,光照30min,降解率可达到96%以上,降解反应符合一级反应动力学.光催化反应可以有效地破坏X-3B的发色基团偶氮结构使其脱色,但在所设定的反应时间(80 min)内X-3B不能被完全矿化,反应过程中有中间产物生成.